 |
 |
 |
|
| Product Information
The XW Power Distribution
Panel (XW PDP) is factory-wired and labeled to support a
codecompliant single-inverter installation. It has
plenty of room to add wiring and breakers to expand the
XW System with up to three inverters, four charge
controllers, or other equipment to support 120/240-volt,
three-wire, single-phase systems. With a
field-reversible door and multiple conduit knockout
locations, the PDP can be configured to mount on either
side of the inverter/charger.
The XW Power Distribution Panel (XW PDP) is
designed to save significant time and money during installation, taking less
than 25 percent of the time to install, when compared to competing solutions. A
mounting plate and XW Conduit Box is supplied with each XW PDP.
Product Compatibility
The distribution panel and conduit box interface
with the following products:
- XW Connection Kit (for second XW Hybrid
Inverter/Charger) and XW Conduit Box
- XW4024, XW4548, and XW6048 Inverter/Chargers
- XW Solar Charge Controllers (requires
customer-supplied breakers and wiring)
- C-Series Charge Controllers (requires
customer-supplied breakers and wiring)
XW PDP
dimensions (H x W x D): 30 x 16 x 8.25” (761 x 406 x 210
mm)
Shipping dimensions (H x W x D): 48 x 21 x 13.5”
(1220 x 533 x 343 mm)
Shipping weight: 67.2 lb (30.5
kg)
XW PDP ships with:
Power
Distribution Panel enclosure with a field-reversible
panel door, pre-wired with:
- Three 60 A, 120/240 Vac, two-pole, Square-D,
Type QOU, DIN-rail mounted AC breakers for AC input, Bypass, and AC Load
- One GJ250A 160 Vdc, 3/8” stud DC breaker
- One ground terminal bus bar
- One neutral terminal bus bar
- One battery negative terminal bus bar
- One pair #4/0 AWG Arctic Ultraflex Blue™ Battery
Cables (factory installed and labeled, ready to connect)
- #6 AWG Arctic Ultraflex Blue™ AC wiring (factory
installed and labeled, ready to connect)
- Room to expand - Five additional AC breaker
positions for two-pole, 60 A Square D, Type QOU breakers; 10 additional DC
breaker positions (eight for charge controller breakers and two for large GJ
inverter breakers)
- Mounting Plate
- XW Conduit Box
|
|
|
|
|
|
 |
|
 |
|
Features
- Maximum Power Point Tracking (MPPT) delivers
maximum available power from PV array to battery bank
- Integrated PV ground-fault protection
- Ultra-reliable, convection-cooled design does
not require a cooling fan − large, aluminum, die-cast heat-sink allows full
output current up to 45°C without thermal derating
- Selectable two or three-stage charging
algorithms with manual equalization to maximize system performance and improve
battery life
- Configurable auxiliary output
- Two-line, 16-character liquid crystal display
(LCD) and four buttons for configuration and system monitoring
- Input over-voltage and under-voltage protection,
output over-current protection, and backfeed (reverse current) protection
(warning and fault messages appear on LCD when unit shuts down as a protective
measure)
- Over-temperature protection and power derating
when output power and ambient temperature are high
- Battery Temperature Sensor (BTS) included −
automatically provides temperaturecompensated battery charging
- Xanbus™-enabled network communications protocol
(developed by Xantrex)
- Communicates settings and activity to other
Xanbus™-enabled devices, such as the XW Hybrid Inverter/Charger, the XW System
Control Panel (XW SCP), XW Automatic Generator Start (XW AGS), and other XW
Solar Charge Controllers.
- Five-year warranty
|
|
|
 |
|
 |
|
|
|
